SAB Goblin 700 RAW yellow + Nexspor BLS

Goblin 700 RAW with Blades S700, S105, Nexspor Brushless 3x BLS4021S, 1x BLS4012T, Servoarm Set

Goblin 700 RAW - the logical intersection of light weight and performance

The new Goblin 700 RAW builds on years of know-how of the SAB Goblin series, but in some respects breaks completely new ground, such as to realize an even lighter design and to get back in the air even cheaper in case of a crash, as well as to further reduce repair times.

Main rotor system

The Goblin 700 RAW uses the proven main rotor and tail rotor combination of the Kraken 700, giving the helicopter a wide usable speed range which makes it extremely interesting both as a 3D grenade and with moderate speed for beginner training. The Goblin RAW can be operated with all kinds of FBL systems, but the rotor system only shows its full flight dynamics with a high-quality FBL gyro such as MSH BRAIN 2. Complementing the holistic design of the system, the Heli Kit is delivered directly with the matching SAB main and tail rotor blades made of CFRP.
    

Gearbox

The gearbox has been designed as a closed, virtually maintenance-free unit, with the housing dome being removable at the top. This facilitates maintenance, saves weight and allows for an enormously compact form factor. The primary drive is a low-noise toothed belt.

The kit includes a 21z pulley for the drive motor. This provides a reduction ratio of 10.1:1.
Optional motor belt pulleys are available under Art. No. H0175-xx-S in different numbers of teeth for individual adaptation of the drive motor.
    


Tail puller with automatic belt tensioner

For the first time, a tail boom made of aluminum is used on a Goblin. This is made of a suitable AL alloy and has a diameter of 30mm. Due to the appropriate choice of material and generous dimensioning, the negative aspects of the aluminum tail boom could be largely approximated to the advantages of the CFRP Mono Boom, which is otherwise obligatory for SAB.
The only factor that had to be taken into account in the design was the thermal expansion of an AL alloy, even though this is a minor factor.  To keep the rear belt tension constant under all temperature ranges, the Goblin 700 RAW is equipped with a belt tensioner as standard.     


Innovative battery insertion

The cab fairing is firmly attached to the chassis and thus constitutes a load-bearing part of the structure. This has enabled the weight to be significantly reduced. The model has a reclosable opening at the front, allowing the drive battery to be conveniently inserted. The H1102-S battery insertion plates are used on the RAW. Thus all owners of a Goblin Kraken 700 can continue to use the battery packs.
    


Technical data SAB Goblin 700 RAW

    Weight Airframe: 2620g (Airframe without blades, drive and electronics)
    Rotor blade length: from min. 650mm to max. 720mm
    Tail rotor blade length: from min. 105mm to max. 115mm
    Main rotor diameter: 1548mm (with the 690mm blades included in the kit)
    Tail rotor diameter: 284mm (with 105mm blades included in the kit)
    Servo mounts suitable for 40mm Std. servos (TS and tail)
    Reduction ratio main rotor: 10,1 : 1 (with the 21z pulley included in the kit)
    Ratio to tail rotor: 4.9 : 1 (with the 26z tail rotor pulley included in the kit)
    Intended motor size: 4525 series (e.g. Xnova 4525 with 500KV to 560KV)
    Intended controller rating: 160A to 200A HV controller
    Intended battery size: 12S LiPo with 4.500mAh to 5.500mAh

Content:
1x Goblin RAW 700 kit with canopy    
    Main rotor blades Carbon S700
    Tail rotor blades Carbon S105
    21z pulley
3x Nexspor Brushless Servo BLS4021S
1x Nexspor Brushless Tailservo BLS4012T
1x Servoarm Set



Required accessories
- Motor 4525-500 - 560KV
- ESC 160A to 200A with BEC
- 12S LiPo battery with 4500mAh to 5500mAh
- FBL Gyro
- RC system

This model helicopter is not suitable for children under 14 years!